Hioki MR8827 Скачать руководство пользователя страница 348

Страница: 348 / 436

343

External I/O

17.2.4 Trigger Output (TRIG OUT)

You can output a signal when a trigger event occurs. This feature allows multiple instruments to be

controlled for parallel synchronous operation.

Signal Output Procedure

Connect the cables for the output signals to the TRIG OUT and GND terminals.

Refer to “17.1 Connect to External Control Terminals” (p. 337).

Press the

SYSTEM

key to open the

[Environment]

sheet, and move the cursor to

[TRIG

OUT]

Select the output signal type for the trigger output terminal.

Pulse

After LOW level output, the signal goes HIGH after a specified interval.

Level

After the trigger occurs, a LOW level signal will be output during waveform

retrieval.

When a trigger event occurs, a pulse wave changing from HIGH (4.0 V to 5.0 V) to LOW (0 V to 0.5

V) will be output from the TRIG OUT terminal.

Output signal

Open drain output (with voltage output) active LOW*

Output voltage range

HIGH level: 4.0 V to 5.0 V

LOW level: 0 V to 0.5 V (current: 15 mA)

Pulse width

Pulse width at pulse setting time: 2 ms ± 1 ms

Pulse width at level setting time: (sampling rate × no. of data points after

trigger) or more

Maximum input voltage

50 V DC 50 mA 200 mW

* Triggering should occur when the signal voltage level changes from HIGH to LOW.

HIGH

4.0 V to 5.0 V

LOW

0 V to 0.5 V

GND

TRIG OUT

100

kΩ

5 V

1 ms or

greater

• Trigger events occur and signals are output when the auto-ranging function is used with the Memory

Function. Keep this in mind when performing auto-range measurement while using the trigger output

terminal.

• When using memory division, the trigger output (TRIG_OUT terminal output) may output the Low

level or output erratically under the following conditions.

•

The timebase is 5 μs/div to 100 μs/div

• The record (measurement) time is 5 ms or less

• Tracking wave display is

[Off]

External Control

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды