Hioki MR8827 Скачать руководство пользователя страница 118

Страница: 118 / 436

113

Manual Printing With the PRINT Key (Selective Printing)

Start and stop the measurement.

Press the

START

key to start measurement.

Press the

STOP

key to stop measurement.

Printing is not possible during measurement. Measurement must

be stopped before printing is started.

•

To output waveform data to

the PC connected via LAN

Model 9333 LAN

Communicator must be

installed on the PC to which

the data is to be output.

For more information

about how to operate and

configure the Model 9333

LAN Communicator, as well

as install it on a PC, see the

instruction manual of Model

9333 LAN Communicator.

•

When setting the output

destination to

[LAN]

The IP addresses of the

instrument and the PC

connected via LAN must be

set. For more information

about how to set the IP

addresses, refer to (p. 310).

Select print contents and execute printing

When you press the

PRINT

key, the

“

Exec Select print

”

GUI

appears on the right side of the screen.

Whole Wave

Print all waveform data in internal memory of the unit.

(

Default setting)

A-B Wave

Print only A and B cursors defined range of waveform

data in the internal memory of the unit. (Memory/

Recorder Function only)

About Trig

Print waveform data for 10 divisions before and after

trigger position. (Memory Function only)

List

Print main settings.

Report

Print the report.

Refer to “6.6.2 Report Print (A4 Size Print)” (p. 118).

When the selection (except for [Cancel]) has been made, printing

starts.

To stop printing before it has finished, press the

STOP

key.

When performing waveform evaluation, the evaluation area will

be printed at the same time. To disable printing of the evaluation

area, set waveform evaluation to

[Off]

. (p. 296)

Printing (

When Model U8350 Printer Unit is installed

)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды