Hioki MR8827 Скачать руководство пользователя страница 331

Страница: 331 / 436

326

Transferring Data to the PC

16.4

Transferring Data to the PC

The supplied USB cable can be used to transfer data from the built-in drive or CF card to a PC.

For information on how to use the supplied application software for data analysis, refer to the application's

Help function.

To Install and startthe application software, refer to “16.5 Wave Viewer (Wv)” (page 327).

System requirements
PC running Windows Vista

, Windows 7, or Windows 8

CAUTION

To avoid equipment failure, do not disconnect the USB cable while communication is in

progress.

Use a common ground for the instrument and PC. Use of different ground circuits will

result in a potential difference between the instrument’s ground and the PC’s ground.

If the USB cable is connected while such a potential difference exists, it may result in

equipment malfunction or failure.

Instrument Settings

Procedure

Press the

SYSTEM

key to open the System screen, and then select the

[Interface]

sheet.

Move the cursor to

[Interface]

, and select

[LAN].

Move the cursor to

[USB Set]

, and select

[Mass storage

HDD]

and

[Mass storage CF].

Operations to the USB memory stick, built-in drive or CF card from the unit are restricted during

[Mass

Storage].

Furthermore, the printer prints at

[Slow/Fine]

, regardless of the

[Print Speed]

setting.

To Connect the USB Cable

Preparations

Stop measurement and make sure that the File screen is not displayed.

USB Connector

(Type B)

Insert the USB cable

into the USB port on the

instrument, being careful

to orient the connector

correctly.

Plug the other end of the

USB cable into a USB

interface on the PC.

Removable disk

Back side

When the connection is established, the PC will recognize the instrument as a removable disk.

The PC can now access data on the built-in drive or CF card of the instrument.

Disconnecting the USB Cable

To disconnect the USB cable of the instrument from a PC that is currently running, use the

[Safely

Remove Hardware]

icon and follow the prescribed steps.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды