Hioki MR8827 Скачать руководство пользователя страница 289

Страница: 289 / 436

284

FFT Analysis Modes

Cross-Correlation Function

Shows the correlation of two points on tow input signals at time differential

t. Output is displayed

as a function of differential time

Main uses:

To determine the phase shift of two signals per unit of time

To determine the speed and distance of time lag between two signals

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Axis

Display type

Description

X axis

Linear

Time display

The center (

= 0) is the reference. To the right is lag time (+

t), and to the left is

lead time (-

Y axis

Lin-Mag

+1 to −1 is displayed in dimensionless units.

At time differential

, this value is +1 when the correlation of input and output

signals is the closest, and 0 when correlation is the least. −1 indicates

completely reversed polarity.

Waveform Example

X axis: Linear

Y axis: Lin-Mag

This instrument provides a circular cross-correlation function.

Analysis results are normalized to the maximum value.

1/1 Octave, 1/3 Octave

Analyze spectrums such as noise using fixed rate spectrum filters of 1/1 octave band or 1/3 octave

band.

Main uses:

To analyze noise frequency

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289), “Octave Filter Characteristics” (p. A24)

Axis

Display type

Description

X axis

Log

Displays the center frequency of each band.

Y axis

Lin-Mag

Displays octave analysis values linearly.

Log-Mag(logarithm)

Displays octave analysis values as dB values. (0 dB reference value: 1eu)*

* eu: engineering units that are currently set are the standard (e.g., when the unit settings is volts, 0 dB = 1 V)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды