Dräger Fabius 4116029 Скачать руководство пользователя страница 99

Страница: 99 / 328

Fabius

Repair Instructions

3-31

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

14.5

Power Transformer

In case of repair, replace the complete power transformer.

14.5.1

Testing the Power Transformer Output Voltage

• Switch control box off using ON/OFF switch (ON/OFF switch is located on rear

panel of control box).

• Unplug power cord from AC outlet.

• Check mains fuses of the control box (mains fuses are located on rear panel of

control box).

• If mains fuses are OK, proceed as follows:

• Remove control box from trolley (see control box chapter "

Removing the Control

Box from the Gas Box

").

• Remove lateral screws

from control box

and lift top cover

in direction of

and away from control box

• Place top cover

of control box

aside.

Fig. 13:

Removing top cover of the control box

Electrostatic discharge can damage electrostatic sensitive
devices. Use a static-dissipative mat and a wrist strap when
handling electrostatic sensitive devices.

1..2..

PEEP

IPPV

man./

spont.

Pmax

TI:TE

TIP:TI

IPPV

IPPV
Paw [mbar]

FiO2

Paw

60
40
20

7.9

12.0

3.0

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 99 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: