Dräger Fabius 4116029 Скачать руководство пользователя страница 321

Страница: 321 / 328

Fabius

Fault-Cause-Remedy

6-3

Cop

ight

2000 Dr

aeger

edical,

sec6_f

aul

tca

usrem

.fm

FLOW INOP

The flow sensor has not
been calibrated.

The flow sensor is faulty.

The flow sensor has been
replaced but not
calibrated.

The flow sensor hose is
faulty.

Calibrate the flow sensor.

Replace the flow sensor and
calibrate it.

Calibrate the flow sensor.

Replace the flow sensor hose and
calibrate the flow sensor.

MEMORY ERROR

Internal data loss.

Switch Fabius off and on.

Inform DrägerService, if
necessary.

MV HIGH

The upper alarm limit for
the minute volume has
been exceeded.

The flow sensor has not
been calibrated.

The flow sensor is faulty.

Calibrate the flow sensor (see
Instructions for Use).

Calibrate the flow sensor.

Replace with new flow sensor and
calibrate new flow sensor.

MV LOW

The minute volume has
decreased below the
lower alarm limit.

The hose is
blocked/kinked.

There is a leak in the
breathing system.

Reduced volume during
pressure limitation.

Reduced lung compliance.

The flow sensor has not
been calibrated.

The flow sensor is faulty.

Check the minute volume.

Check the hose system.

Check the breathing system.

Leak test the breathing system.

Adjust the ventilation parameters
correctly.

Calibrate the flow sensor.

Replace with new flow sensor and
calibrate new flow sensor.

Fault

Cause

Remedy

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 321 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: