manualshive.com logo in svg

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 209 / 328

Поделиться
Скачать
Dräger Fabius 4116029 Скачать руководство пользователя страница 209

Fabius

®

Repair Instructions

 

3-141

Cop

yr

ight

 2000 Dr

aeger

 M

edical,

 In

c.

sec3_r

epai

rinstruc_c.fm

 

Fig.139:

Contact assignments of different rechargeable batteries used in Fabius

• Replace rechargeable batteries with new rechargeable batteries.

• Mount cable lugs (see Figure above). Check that connections are correct before 

installing rechargeable batteries.

• Mount new rechargeable batteries to Fabius using angular mount. Do not forget 

to reconnect the ground line.

• Check whether you can switch on the device without AC power.

• Mount cover to rear panel of Fabius.

• Charge new batteries by connecting Fabius to AC outlet, switching Fabius on, 

and leaving it connected to AC outlet for 4 hours.

WARNING:

Risk of personal injury. 
No uninterruptible power supply in case of power failure if 
rechargeable batteries are not connected correctly. Make sure to 
connect rechargeable batteries correctly.

Rechargeable batteries from Sonnenschein and Panasonic have 
different contact assignments. Reversing the contacts may 
damage the device or blow the fuse (in the holder).

Strictly follow the contact assignments of the different 
rechargeable battery types when replacing rechargeable 
batteries (see Figure below).

Sonnenschei

Panasonic

Sonnenschei

Panasonic

white

brown

brown

white

fuse

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Отзывы:

Нет отзывов