manualshive.com logo in svg

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 64 / 328

Поделиться
Скачать
Dräger Fabius 4116029 Скачать руководство пользователя страница 64

Fabius

®

Function Description

2-56

Cop

yr

ight

 2000 Dr

aeger

 M

edical,

 In

c.

sec2_

funcde

scr

ip_

b.fm

 

10.7.8

PEEP Key

After pressing the PEEP key, the positive end-expiratory pressure may be set in a 
range of 1 hPa (mbar) to 15 hPa (mbar). The set value has immediate effect.

10.7.9

Limit Values Key

The limit values key is used to set the upper and the lower limit values within a certain 
range.

10.7.10 Calibration Key (–0–)

After pressing the calibration key (–0–), the differential pressure sensor and the O

2

 

sensor are calibrated. The O

2

 sensor is calibrated to 21 vol.% or 100 vol.%.

10.7.11 2-Min Silence Key

After pressing the 2-min silence key, the audible alarm is silenced for 2 minutes. This 
status is indicated by the yellow LED in the silence key. Pressing the silence key again 
during the alarm silence time will reset the audible alarm.

10.7.12 Standby Key

After pressing the standby key, the control box switches over to standby mode.

10.7.13 Menu Key

After pressing the menu key, it is possible to configure Fabius.

10.7.14 Screen Page Key

After pressing the screen page key, it possible to select different screen pages.

10.7.15 Control Knob

The control knob is used to change patient parameters (for example, PEEP, V

T

, or 

P

max

) by turning (selection of data) and pressing (confirmation of selected data).

10.8

Interface

The interface is use to transmit the analog voltages to the pneumatics.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Отзывы:

Нет отзывов