Dräger Fabius 4116029 Скачать руководство пользователя страница 87

Страница: 87 / 328

Fabius

Repair Instructions

3-19

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

Motor error

Ventilator drive error: no
incrementing possible. End
position switch activated
continuously. End position switch
not detected.

For current code and error
description, see display field
“VEN”.

Error may also occur if Fabius
is operated while ventilator is
not connected.

24 V operating voltage

Relay of Power PCB switched off.

Open fuse F4 on Power Supply
PCB.

End position of actuator exceeded.

Incremental encoder lost
increments.

Diaphragm pressure too low.

Ventilator cover open.
Vacuum hose disconnected.
Diaphragm pump needs replaced.

Diaphragm pressure too high.

Diaphragm pressure sensor
connector disconnected.

Diaphragm pressure sensor
needs replaced.

Error may also occur if Fabius
is operated while ventilator is
not connected.

System temperature too high.

Error occurred on Power PCB.

Time-out in IPPV/ventilation not
OK.

Motor open or disconnected.
Power PCB needs replaced.

Error may also occur if Fabius
is operated while ventilator is
not connected.

SIO error

There is an interruption of the
communication line.
The controller (Power PCB) does
not function.

Motor current too high.

Power amplifier needs replaced.
Motor open.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 87 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: