Dräger Fabius 4116029 Скачать руководство пользователя страница 185

Страница: 185 / 328

Fabius

Repair Instructions

3-117

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

19.2.8

Testing the O

Concentration (O

O Ratio)

Concentration Test

• Make sure O

sensor is functioning properly and has been calibrated.

• After adjusting/readjusting S-ORC valve, check O

concentration using an O

analyzer (accuracy: 1 vol.% O

• If you do not need to adjust/readjust the previous S-ORC valve settings or if you

have replaced the S-ORC, test according to Test Certificate using an O

analyzer

(accuracy: 1 vol.% O

19.2.9

Flow Test

• Fully open N

O flow control valve.

• Slowly open O

flow control valve.

While the O

flow increases, the N

O flow should increase to more than 9 L/min.

• Close O

flow control valve slowly and evenly.

The N

O flow should decrease slowly and evenly.

• Test S-ORC using Test Certificate.

Flow (L/min)

Concentration (vol.%
O

)

0.5 L/min
±0.05 L/min

Fully open N

O flow

control valve.

22 to 33

1.0 L/min ±0.1 L/min

22 to 28

3.0 L/min ±0.2 L/min

22 to 33

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 185 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: