Dräger Fabius 4116029 Скачать руководство пользователя страница 227

Страница: 227 / 328

Fabius

Repair Instructions

3-159

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

22.4.4

Calibrating the PEEP Valve (software 2.00 or higher)

In software version 2.00 or higher, the electronic PEEP valve is calibrated
automatically in the DrägerService Mode.

• Connect complete circle absorption system.

• Switch control box on.

• Calibrate O

sensor in the standby mode.

• Calibrate flow sensor in the standby mode.

• Press “Menu” key.

• Select “configuration”.

• Confirm selection by pressing rotary knob.

• Select “keycode” by turning rotary knob.

• Confirm selection by pressing rotary knob.

• Select “112” by turning rotary knob.

• Confirm selection by pressing rotary knob.

• Select “Cal. pressure” by turning rotary knob.

• Confirm selection by pressing rotary knob.

Fabius calibrates the pressure sensor (Paw).

• Connect a corrugated hose between the inspiratory nozzle and the expiratory

nozzle.

• Close all flow control valves.

• Disconnect the breathing bag.

• Select “Cal. peepvalve” by turning the rotary knob.

• Confirm your selection by pressing the rotary knob.

• Do not disturb the calibration procedure.

Fabius automatically calibrates the electronic PEEP valve. After completion of the
automatic calibration, the message "OK" appears on the display of the control box.

If the message "OK" is not displayed, proceed as follows:

• Repeat calibration as described above.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Содержание Fabius 4116029









































































































































































































































































































































Результаты поиска

Содержание Fabius 4116029

Отзывы:

Dräger Fabius 4116029, Техническое и сервисное руководство, Страница: 227 / 328

Результаты поиска

Содержание Fabius 4116029

Отзывы: