Cisco WS-C3550-12G Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 436

background image

8-31

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

GE-WAN Interface Management Window

The following tabs are available on the GE-WAN Interface Management window:

•

Status Tab

•

Configuration Tab

•

Performance Tab

•

Routing Protocol Tab

•

HSRP Tab

•

Additional Notes Tab

Status Tab

The Status tab of the GE-WAN Interface Management window consists of a single are by the same name.
The Status area provides the following information to describe the general characteristics of the
interface:

•

Description—Comment or a description to help you remember what is attached to this interface. The
description is only put in the configuration to help you remember what specific interfaces are used
for.

•

Index—String index of the interface. This attribute is read-only.

•

Speed—Describes the physical interface speed. This attribute is read-only.

•

Operational Status—The current operational state of the interface. This attribute is read-only. This
attribute has one of the following values:

–

other

–

ok

–

minorFault

–

majorFault

•

Administrative Status—The desired state of the interface. This attribute has one of the following
values:

–

testing (read-only)—Indicates that no operational packets can be passed.

–

up

–

down

•

Last Change—The value (in seconds) of sysUpTime at the time the interface entered its current
operational state. If the current state was entered before the last reinitialization of the local network
management subsystem, then this object contains a zero value. This attribute is read-only.

•

Connector Present—Indication if a cable is connected to the interface. If the ifAdminStatus is down,
then this value cannot be determined and an “unknown” message is given. This attribute is read-only.
This attribute has the following values:

–

yes—Cable is connected to the interface.

–

no—Cable is not connected to the interface.

–

unknown—Cannot determine if a cable is connected to the interface.

•

Number of Resets—Number of times the interface internally reset. This attribute is read-only.

«
...
175
176
177
178
179
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: PROception Страницы: 13

Бренд: Ubiquiti Страницы: 24

Бренд: TRENDnet Страницы: 36

Бренд: TP-Link Страницы: 2

DECT 1615 Series

Бренд: Uniden Страницы: 28

Nfiniti WHR-HP-GN

Бренд: Buffalo Страницы: 43

Бренд: linkPro Страницы: 49

Бренд: Cambium Networks Страницы: 24

Бренд: Acksys Страницы: 36

Бренд: Yamaha Страницы: 2

Wi-REACH Classic

Бренд: Connect One Страницы: 38

Бренд: ADB Страницы: 35

Бренд: ADB Страницы: 38

Бренд: Redpine Signals Страницы: 62

Бренд: 2xWireless Страницы: 12

Бренд: Nimbus Water Systems Страницы: 10

Бренд: Canyon Страницы: 8

Бренд: Canyon Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды