manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 325

 

10-17

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

VLAN Management Window

Root Election 

The Root Election area provides the following information: 

•

Root Preference—STP root priority. This attribute may has following values:

–

none (0)

–

primary (1)

–

secondary (2)

•

Hello Time—Hello-time in seconds.

•

Diameter—Specifies the network diameter (maximum number of bridges between two end nodes). 
If specified, the switch will calculate the optimal hello-time, forward-time, and max-age. User may 
optionally specify an explicit hello-time.

•

Set Root—Configures the root priority of the device in the VLAN STP instance. This action will set 
the VLAN STP bridge-priority and reset the hello-time, forward-delay, and max-age timers. This 
action does not guarantee that the switch will be elected the STP root, it only sets these values.

Advanced 

The Advanced area allows you to configure the attributes described in this section. While these attributes 
are configurable, this is not the recommended method for configuring them. Alternately, if you specify 
a network diameter but no hello time, forward-delay timer, or max-age timer, using the Set Root button 
(in the Root Election Area) causes the switch to automatically calculate the optimal hello time, 
forward-delay timer, and max-age timer for that diameter.

•

Hello Time—Indicates how often the switch broadcasts hello messages to other switches in the STP 
domain. If there is no spanning tree instance for the VLAN, value is nil. You can optionally provide 
a diameter and hello-time to override the calculated value. If no diameter or hello-time are provided, 
the switch will use the default hello time of 2 seconds.

•

Priority—Spanning tree bridge priority. If there is no spanning tree instance for the VLAN, the value 
is nil.

•

Forward Delay—Forward delay timer for STP state transitions. Determines how long each of the 
listening and learning states will last before the interface begins forwarding. If there is no spanning 
tree instance for the VLAN, the value is nil. If no diameter is specified, the switch will use the 
default delay of 15 seconds.

•

Max Age—Describes the amount of time that STP protocol information received by a switch is 
stored before it expires. If there is no spanning tree instance for the VLAN, the value is nil. If no 
diameter is specified, the switch will use the default duration of 20 seconds.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды