Cisco WS-C3550-12G Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 436

background image

8-104

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

Serial Subinterface Management—Configuration Window

Routing Protocol Tab

The following areas are available on the Routing Protocol tab of the Serial Subinterface
Management—Configuration window:

•

OSPF

•

EIGRP

•

IS–IS

OSPF

The OSPF area provides the following information. All the attributes in this area are read-only.

•

Area ID—The predefined ID uniquely identifying the area to which the interface connects. It can be
specified as either a decimal value or as an IP address. Value is 0.0.0.0 if the interface is a Layer 2
(no IP address assigned) interface. This attribute is read-only.

•

Network Type—OSPF interface type. By default, a POS interface is point-to-point, however, the
OSPF network type may be modified to accommodate different types of network configurations.
This attribute has one of the following values:

–

broadcast

–

nbma

–

pointToPoint

–

pointToMultipoint

•

Authentication Key—Password to be used by neighboring OSPF routers on a network segment that
is using OSPF simple password authentication. Ignored if Authentication Type is not “simple”.

•

Hello Interval (sec)—Frequency at which the device will send hello packets on the specified
interface and EIGRP autonomous system number.

•

Trans. Priority—The priority of this interface. Used in multiaccess networks, this field is used in the
designated router election algorithm. The value 0 signifies that the router is not eligible to become
the designated router on this particular network. If more than one router has the same value for this
field, the routers use their router ID as a tie breaker.

•

Trans. Dead (sec)—Number of seconds that a device’s hello packets must not have been seen before
its neighbors declare the OSPF router down. Must be consistent among all routers on an attached
network.

•

Trans. Delay (sec)—The estimated number of seconds it takes to transmit a link state update packet
over this interface.

•

Retrans. Interval (sec)—The number of seconds between link-state advertisement retransmissions
for adjacencies belonging to this interface. This value is also used when retransmitting database
description and link-state request packets.

«
...
248
249
250
251
252
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: TRENDnet Страницы: 44

Бренд: EnGenius Страницы: 73

Бренд: CNET Страницы: 2

Бренд: ReadyNet Страницы: 2

Бренд: Cerio Страницы: 53

Бренд: sauter Страницы: 8

Бренд: Airlink101 Страницы: 15

Бренд: Loopcomm Страницы: 40

Бренд: Linksys Страницы: 25

Бренд: 4IPNET Страницы: 22

Бренд: 4IPNET Страницы: 80

Бренд: 4IPNET Страницы: 83

Powerline 802.11g Wireless Access Point

Бренд: Allnet Страницы: 6

Бренд: Allnet Страницы: 27

Бренд: Allnet Страницы: 25

Бренд: Allnet Страницы: 25

Бренд: Allnet Страницы: 34

Бренд: Allnet Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды