manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 193

 

8-47

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

POS Interface Management Window

SONET 

The SONET area contains the following information:

•

SONET Overhead J0 Byte—Value of the SONET overhead section trace byte. A value of 0x10 is 
for interoperability with some Synchronous Digital Hierarchy (SDH) devices in Japan. This attribute 
is read-only. 

•

SONET Overhead C2 Byte—Value of the SONET overhead path signal identifier. This attribute is 
read-only. These are possible values:

–

0xCF = PPP or HDLC

–

0x13 = ATM

•

SONET Overhead S1 S0 Bits—Value of the SONET overhead S1 & S0 bits. These bits are part of 
the payload pointer byte. This attribute is read-only. These are possible values:

–

0 = OC-3c

–

2 = AU-4

Performance Tab

The following areas are available on the Performance tab of the POS Interface Management window:

•

Packets/Octets Statistics 

•

Error Statistics 

•

Performance Logging 

Packets/Octets Statistics 

The Packets/Octets Statistics area contains the following information:

•

Bandwidth Util (%)—Percentage of bandwidth utilization.

•

In Octets—Total number of received octets including framing characters.

•

Out Octets—Total number of transmitted octets including framing characters.

•

In Unicast Pkts.—The number of packets delivered by this sublayer to a higher (sub)layer, which 
were not addressed to a multicast or broadcast address at this sublayer.

•

Out Unicast Pkts.—The total number of packets that higher-level protocols requested be 
transmitted, and which were not addressed to a multicast or broadcast address at this sublayer, 
including those that were discarded or not sent.

•

In Packets/Sec—Five-minute exponentially decayed moving average of input packets per second.

•

Out Packets/Sec—Five-minute exponentially decayed moving average of output packets per second.

•

In Bits/Sec—Five-minute exponentially decayed moving average of input bits per second.

•

Out Bits/Sec—Five-minute exponentially decayed moving average of output bits per second.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды