manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 322

 

10-14

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

VLAN Management Window

VLAN Membership Tab

The VLAN Membership tab of the VLAN Management window consists of a single area of the same 
name. The VLAN Membership area displays the members of the selected VLAN and the following:

•

VLAN Membership Table—Members are identified by the slot and port numbers in the table.

•

Add/Remove Members—Adds or removes a VLAN member. Launches the VLAN 
Management—Membership Configuration window.

Figure 10-6 VLAN Management—Membership Configuration Window

The following is displayed on the VLAN Management—Member Configuration window:

–

VLAN Member Slot—Indicates the slot where the interface to be added or removed to/from a 
VLAN exists.

–

VLAN Member Port—Indicates the port where the interface to be added or removed to/from a 
VLAN exists.

–

Add Member—Adds the interface, as indicated by the entries in the VLAN Member Slot and 
VLAN Member Port fields, to the VLAN membership.

–

Remove Member—Removes the interface, as indicated by the entries in the VLAN Member 
Slot and VLAN Member Port fields, from the VLAN membership.

–

Allow on Trunk—Permits the configured VLAN member on the trunk.

–

Disallow on Trunk—Denies the configured VLAN member on the trunk.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды