manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 62

 

4-2

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 4      Deploying the Cisco Catalyst Switch Manager

Container (Site, Bay, etc.)

Network Element

Chassis

    Power Supplies

    Supervisor Modules

        Ethernet Interfaces

    Ethernet Modules

        Ethernet Interfaces

    Switch Fabric Modules

    FlexWAN Modules

        Port Adapter

        ATM Port Adapter

            ATM SONET Interfaces

            ATM E3 Interfaces

            ATM T3 Interfaces

    OSM GeWAN Modules

        OSM GeWAN Interfaces

    OSM PoS Modules

        Ethernet Interfaces

        OSM PoS Interfaces

    OSM Channelized SONET Modules

        Ethernet Interfaces

        OSM Channelized SONET Interfaces

            OSM Serial Sub-interfaces

            OSM PoS Sub-interfaces

    Content Switching Modules

Software

    EtherChannels

    Syslog

    EIGRP

    BGP

    OSPF

    VTP

    VLANS

        VLAN_1-205

            VLAN-1

            VLAN-2

            VLAN-3...

        VLAN_206-410

            VLAN-206

            VLAN-207

            VLAN-208...

        VLAN_411-615...

            VLAN-411

            VLAN-412

            VLAN-413...

    STP

    IS-IS

    ACL

    NDE

    Loopback

    QoS

        QoS Policy Map

The top-level Network Element object represents the entire switch including the physical and logical 
components of the switch. The Chassis object, which is a child of the Network Element object, 
represents all the physical components of the switch. For example, the chassis frame, power supplies, 
modules, and ports are all represented under the Chassis object. The Software object, which is a peer of 
the Chassis object, represents all the logical components of the switch. For example, VLAN 
configurations, EtherChannels, and routing protocols are represented under the Software object.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды