Cisco WS-C3550-12G Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 436

background image

8-77

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

ATM/T3 Interface Management Window

Layer 3

The Layer 3 area contains the following information:

•

IP Address—Displays the IP address of the layer 3 interface.

•

Netmask—Subnet mask of the interface IP address. Enabled bits indicate the network addressing
bits in the IP address.

•

Clear IP Address—After receiving confirmation, will remove the IP address setting for this
interface.

Private VLAN Edge

The Private VLAN Edge area provides the following information:

•

Status—Displays the status of private VLAN edge configuration on the interface. Status may be one
of the following values:

–

Enabled

–

Disabled

–

Not Applicable—VLANs are not supported on the device

•

Enable—Enables configuration of the private VLAN edge on the interface.

•

Disable—Disables configuration of the private VLAN edge on the interface.

Actions

The Actions area provides the following information:

•

Commission—This button is used to commission the object manually. This can only be done if the
object is in a decommissioned state. Clicking this button commissions the selected interface.

•

Decommission—This button is used to decommission the object manually. In the decommissioned
state, the properties of the object are not monitored. As a result, data displayed in the configuration
window is not guaranteed to be current. Clicking this button decommissions the interface.

ATM/T3 Tab

The following areas are available on the Performance tab of the ATM/T3 Interface Management window:

•

ATM

•

T3

«
...
221
222
223
224
225
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: Homefibre Страницы: 2

WG602v3 - Wireless Access Point

Бренд: NETGEAR Страницы: 2

Бренд: Lanpro Страницы: 3

HT-TM01 TripMate

Бренд: Hootoo Страницы: 47

Бренд: Foxconn Страницы: 28

Бренд: Binatone Страницы: 14

Бренд: MikroTik Страницы: 4

AirStation Nfiniti WZR-AG300NH

Бренд: Buffalo Страницы: 48

Бренд: Motion Страницы: 26

Бренд: Yunlink Страницы: 27

Бренд: YUNKE CHINA Страницы: 35

Бренд: AmbiCom Страницы: 8

Бренд: EnGenius Страницы: 71

Бренд: PHICOMM Страницы: 5

Бренд: IOGear Страницы: 20

Бренд: RFM Страницы: 52

JWNR2000 - Wireless- N 300 Router

Бренд: NETGEAR Страницы: 144

Бренд: AMX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды