Cisco WS-C3550-12G Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 436

background image

7-21

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 7 Module and Port Adapter Management

SLB Module Management Window

Inventory

The Inventory area provides the following information. All the attributes in this area are read-only.

•

Model—Model of the Content Switching Module.

•

Type—The type of module.

•

Number of Ports—The number of internal ports in the module.

•

Serial Number—The serial number of the module.

•

Hardware Version—The hardware version on the module.

•

Software Version—The software version on the module.

•

Firmware Version—The firmware version on the module.

SLB Setting

The SLB Setting area provides the following information:

•

Forwarding Mode—The current SLB operating mode. This attribute has one of the following values.
This is a read-only attribute.

–

csm(1)

–

rp(2)

•

Configured Mode—The current configured SLB mode. This attribute has one of the following
values:

–

csm(1)

–

rp(2)

Note

The configured SLB mode does not take effect until the Content Switching Module is reloaded. The
reload is performed manually by executing the IOS config mode command power cycle module
slot_number.

Note

When changing the configured SLB mode from CSM to RP, the SLB configurations for CSM will be
erased.

Actions

The Actions area provides the following actions:

•

Commission—This button is used to commission the object manually. This can only be done if the
object is in a decommissioned state.

•

Decommission—This button is used to decommission the object manually. In the decommissioned
state, the properties of the object are not monitored. As a result, data displayed in the configuration
window is not guaranteed to be current.

The decommission action allows a Content Switching Module to be removed and replaced without
generating alarms.

«
...
131
132
133
134
135
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: Ocens Страницы: 2

Бренд: T-Mobile Страницы: 4

Бренд: Positron Страницы: 36

Бренд: Gemtek Systems Страницы: 13

Бренд: FS Страницы: 12

Бренд: UniFi Страницы: 45

Бренд: NETGEAR Страницы: 2

Бренд: Ebyte Страницы: 13

Бренд: E-TOP Страницы: 93

AirPremier DWL-7100AP

Бренд: D-Link Страницы: 76

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 36

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды