manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 123

 

7-11

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 7      Module and Port Adapter Management

Ethernet Module Management Window

Note

If this attribute has a value other than ok, an alarm is generated.

•

Administrative Status—Displays the administrative status of the Ethernet module. This attribute can 
have one of the following values:

–

Enabled

–

Disabled

–

Reset

–

Out of Service

–

Admin

•

Last Reset Reason—Displays the reason for the most recent module reset.

–

Unknown

–

Power Up

–

Parity Error

–

Clear Config Reset

–

Manual Reset

•

Last Status Change Time—Displays the time stamp of the most recent module status change.

Management Tab

The following areas are available on the Management tab of the Ethernet Module Management window:

•

Actions 

•

Performance Logging 

Actions 

The Actions area provides the following information:

•

Commission—This button is used to commission the object manually. This can only be done if the 
object is in a decommissioned state. Clicking this button commissions all interfaces.

•

Decommission—This button is used to decommission the object manually. In the decommissioned 
state, the properties of the object are not monitored. As a result, data displayed in the configuration 
window is not guaranteed to be current. Clicking this button decommissions all interfaces.

The decommission action is useful to allow a Ethernet module to be removed and replaced without 
generating alarms.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды