Cisco WS-C3550-12G Скачать руководство пользователя страница 37

Страница: 37 / 436

1-7

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 1 Product Overview

Supported Hardware

OSM-4CHOC12/T3-SI

4-port channelized OC-12 OSM, SI, with 4 ports of Gigabit Ethernet

OSM-8CHOC12/T3-MM

8-port channelized OC-12 OSM, MM, with 4 ports of Gigabit Ethernet

OSM-8CHOC12/T3-SI

8-port channelized OC-12 OSM, SI, with 4 ports of Gigabit Ethernet

PA-2E3

2 Port E3 Serial Port Adapter with E3 DSUs

PA-2H

2-Port HSSI Port Adapter

PA-2T3

2 Port T3 Serial Port Adapter

PA-2T3+

2 Port T3 Serial Port Adapter Enhanced

PA-4T+

4 Port Serial Port Adapter, Enhanced

PA-8T-232

8-Port Serial, 232 Port Adapter

PA-8T-V35

8-Port Serial, V.35 Port Adapter

PA-8T-X21

8-Port Serial, X.21 Port Adapter

PA-A3-E3

1-Port ATM Enhanced E3 Port Adapter

PA-A3-OC3MM

1-Port ATM Enhanced OC3c/STM1 Multimode Port Adapter

PA-A3-OC3SMI

1-Port ATM Enhanced OC3c/STM1 Singlemode (IR) Port Adapter

PA-A3-OC3SML

1-Port ATM Enhanced OC3c/STM1 Singlemode (LR) Port Adapter

PA-A3-T3

1-Port ATM Enhanced DS3 Port Adapter

PA-E3

1 Port E3 Serial Port Adapter with E3 DSU

PA-H

1-Port HSSI Port Adapter

PA-MC-2T3+

2 port multichannel T3 port adapter

PA-MC-8E1/120

8 port multichannel E1 port adapter with G.703 120ohm interface

PA-MC-8T1

8 port multichannel T1 port adapter with integrated CSU/DSUs

PA-MC-E3

1 port Multi-Channel E3 port adapter

PA-MC-T3

1 port multichannel T3 port adapter

PA-POS-OC3MM

1-Port Packet/SONET OC3c/STM1 Multimode Port Adapter

PA-POS-OC3SMI

1-Port Packet/SONET OC3c/STM1 Singlemode (IR) Port Adapter

PA-POS-OC3SML

1-Port Packet/SONET OC3c/STM1 Singlemode (LR) Port Adapter

PA-T3

1 Port T3 Serial Port Adapter

PA-T3+

1 Port T3 Serial Port Adapter Enhanced

PA-A3-8E1IMA

8-port ATM Inverse Mux E1 (120 Ohm) Port Adapter

PA-MC-4T1

4 port multichannel T1 port adapter with integrated CSU/DSUs

GE-WAN2

2-port Gigabit Ethernet

Table 1-1

Supported Hardware (continued)

Part Number

Description

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Результаты поиска

Содержание WS-C3550-12G

Отзывы:

Бренды по названию

Популярные бренды

Cisco WS-C3550-12G, Руководство пользователя

Результаты поиска

Содержание WS-C3550-12G

Отзывы:

Бренды по названию

Популярные бренды