Cisco WS-C3550-12G Скачать руководство пользователя страница 271 | Manualshive

Страница: 271 / 436

Cisco WS-C3550-12G Скачать руководство пользователя страница 271

9-7

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 9 Software Management

Software Management Window

•

Backup File—The name of the file to which the startup configuration will be copied.

Note

If the TFTP server is not the Cisco EMF server, then the file specified by the Backup File field
must already exist. If it does not, the backup action will fail. If the TFTP server is the Cisco EMF
server, the file will be automatically created.

•

Backup—Backs up the current startup configuration to the TFTP server. The backup filename is
specified by the Backup File attribute.

•

Scheduled Backup—Schedules the backup operation. Launches the Schedule dialog box which
consists of the following:

–

Date—The date when the restore will start. The format is MM/DD/YYYY.

–

Hour—The hour when the restore will start. It is a 24-hour clock.

–

Minute—The minute when the restore will start.

•

Restore Status—Status of the last restore action. This attribute (read-only) has the following values:

–

Ok—The restore operation completed successfully.

–

Failed—The restore operation failed.

–

Not executed—The restore operation was not executed.

•

Restore File—The name of the configuration file that will be restored.

•

Restore—Restores the file specified in the Restore File attribute from the TFTP Host to the startup
configuration.

•

Scheduled Restore—Schedules the restore operation. Launches the Schedule dialog box which
consists of the following:

–

Date—The date when the restore will start. The format is MM/DD/YYYY.

–

Hour—The hour when the restore will start. It is a 24-hour clock.

–

Minute—The minute when the restore will start.

Note

The switch or router needs to be reset for the new configuration to take effect.

Tip

The configuration Backup/Restore actions are used to upload the switch or router startup configuration
to a server. The configuration can then be edited on the server and downloaded back to the switch or
router.

«
...
269
270
271
272
273
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды