manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 251

 

8-105

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

Serial Subinterface Management—Configuration Window

EIGRP 

The EIGRP area provides the following information:

•

Interface—Describes the EIGRP configuration of the interface on each active autonomous system. 
The EIGRP parameters of the interface on an autonomous system may be explicitly configured even 
if EIGRP routing updates in the autonomous system are not currently carried on the interface.

•

Bandwidth Utilization (%) —The percentage of the interface bandwidth that the EIGRP protocol 
can use.

•

Hold Time (sec)—Hold time during which the device will wait for a hello packet to be received on 
the specified interface and EIGRP autonomous system number. The hold time should be at least 
three times the hello interval.

•

Hello Interval (sec)—Frequency at which the device will send hello packets on the specified 
interface and EIGRP autonomous system number.

IS-IS 

The IS-IS area provides the following information:

•

Status—Indicates whether IS-IS routing is enabled or disabled.

•

Area Tag—The IS-IS routing area in which the interface participates. If multi-area IS-IS is 
configured on the device, the IS-IS area must be named; otherwise, this value may be an implicit 
null tag.

•

Level 1 Hello Interval—Length of time between hello packets generated on the interface for level 1 
routing.

•

Level 2 Hello Interval—Length of time between hello packets generated on the interface for level 2 
routing.

•

Level 1 Metric—Cost of the interface for IS-IS level 1 (intra-area) route calculation.

•

Level 2 Metric—Cost of the interface for IS-IS level 2 (inter-area) route calculation.

•

Level 1 Priority—The priority is used to determine which router on a LAN will be the designated 
router or designated intermediate system (DIS). 

•

Level 2 Priority—The priority is used to determine which router on a LAN will be the designated 
router or DIS.

•

Enable—Enables IS-IS routing on the subinterface.

Note

To enable IS-IS on an interface, the user must specify an IS-IS routing process that is already 
deployed on the device. If the process does not exist, the action will fail.

•

Disable—Disables IS-IS routing on the subinterface.

Note

By default, all interfaces are configured as IS-IS Circuit-type Level 1-2.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды