manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 395

 

12-7

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 12      Profile Management

Syslog Profile

Creating a Syslog Profile

To create a Syslog profile, follow these steps:

Step 1

Launch the Network Element Management Profile window by performing one of the following:

•

Right–click a Site object within the Network or Physical containment views, then choose 
CSM/7600 Manager > Logical > Software > Syslog Profile.

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose Logical > Software > Syslog Profile.

•

Right–click a Software object within the Physical containment view, then choose Syslog Profile.

The Syslog Management Profile window appears (see 

Figure 12-3

).

Step 2

Enter the name for the new profile at the prompt, then click Ok.

The newly created profile is displayed in the profile list on the left-hand side.

Step 3

Select the profile from the profile list.

Step 4

Specify the values for the profile attributes in the Syslog Configuration (IOS) and Syslog Configuration 
(Catalyst OS). The fields within each of these areas are as follows:

•

Max. Table Entries—The maximum number of messages in the syslog table. When this limit has 
been reached, the oldest messages are deleted to make room for newer messages.

•

Max. Syslog Severity—The maximum severity that will be recorded. Messages with a higher 
numeric value of severity will not be recorded. This attribute has one of the following values (listed 
in ascending order of severity):

–

emergency (1)

–

alert (2)

–

critical (3)

–

error (4)

–

warning (5)

–

notice (6)

–

info (7)

–

debug (8)

Note

The greatest severity state has the smallest numeric value of severity. For example, the 
emergency state has a value of (1) and is more severe than the info state, which has a value of 
(7). If you set Max. Syslog Severity to 7, then all states except debug will be recorded. This is 
because the debug state has a value of (8), which is greater than the value of the Max. Syslog 
Severity attribute.

•

Enable Notifications—SNMP syslog notifications are sent whenever a new syslog message is 
generated and recorded.

–

true—Notifications enabled.

–

false—Notifications disabled.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды