Cisco WS-C3550-12G Скачать руководство пользователя страница 203 | Manualshive

Страница: 203 / 436

background image

8-57

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

Channelized SONET Interface Management Window

Private VLAN Edge

The Private VLAN Edge area provides the following information:

•

Status—Displays the status of private VLAN edge configuration on the interface. Status may be one
of the following values:

–

Enabled

–

Disabled

–

Not Applicable—VLANs are not supported on the device

•

Enable—Enables configuration of the private VLAN edge on the interface.

•

Disable—Disables configuration of the private VLAN edge on the interface.

Actions

The Actions area provides the following information:

•

Commission—This button is used to commission the object manually. This can only be done if the
object is in a decommissioned state. Clicking this button commissions the selected interface.

•

Decommission—This button is used to decommission the object manually. In the decommissioned
state, the properties of the object are not monitored. As a result, data displayed in the configuration
window is not guaranteed to be current. Clicking this button decommissions the interface.

Performance Tab

The following areas are available on the Performance tab of the Channelized SONET Interface
Management window:

•

Interface Packets/Octets Statistics

•

Interface Error Statistics

•

SONET Section Error Statistics

•

SONET Line Error Statistics

•

SONET Far End Line Error Statistics

Interface Packets/Octets Statistics

The Interface Packets/Octets Statistics area contains the following information:

•

Bandwidth Util (%)—Percentage of bandwidth utilization.

•

In Octets—Total number of received octets including framing characters.

•

Out Octets—Total number of transmitted octets including framing characters.

•

In Unicast Pkts.—The number of packets delivered by this sublayer to a higher (sub)layer, which
were not addressed to a multicast or broadcast address at this sublayer.

•

Out Unicast Pkts.—The total number of packets that higher-level protocols requested be
transmitted, and which were not addressed to a multicast or broadcast address at this sublayer,
including those that were discarded or not sent.

•

In Packets/Sec—Five-minute exponentially decayed moving average of input packets per second.

«
...
201
202
203
204
205
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

FortiAP FAP-U321EV

Бренд: Fortinet Страницы: 31

MSR900-E Routers

Бренд: H3C Страницы: 2

Бренд: Waxess Страницы: 27

WGR612 - 54 Mbps Wireless Router

Бренд: NETGEAR Страницы: 2

TG-RouterE-PM-01-100

Бренд: Telegesis Страницы: 9

Бренд: Nox Medical Страницы: 36

Бренд: AmbiCom Страницы: 6

Бренд: PHICOMM Страницы: 53

Бренд: Kaon Страницы: 30

Бренд: HPE Страницы: 4

Бренд: PI Manufacturing Страницы: 43

Бренд: AirLive Страницы: 62

Бренд: Spectrum Страницы: 2

Cerberus [P 6367]

Бренд: Pentagram Страницы: 48

Бренд: Intellinet Страницы: 6

Бренд: Intellinet Страницы: 17

Бренд: Juniper Страницы: 8

Бренд: Digitus Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды