Cisco WS-C3550-12G Скачать руководство пользователя страница 382 | Manualshive

Страница: 382 / 436

background image

11-30

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

BGP Management Window

•

IS-IS Routing Level—Indicates IS-IS route level redistribution. This field has the following values:

–

level-1—Local area/intra-area dedistribution.

–

level-1-2—Redistribution for both inter and intra-area routing.

–

level-2—Backbone/interarea redistribution (default).

•

Metric—BGP metric used to weigh the redistributed route. If no value is specified for Default Metric
(in the BGP tab), this value defaults to 0.

•

Add Redistribute—Enables route redistribution from another IP routing process into the BGP
routing domain. Routes may be learned from an IS-IS, EIGRP, or OSPF routing process.

•

Delete Redistribute—Disables route redistribution from another IP routing process into the BGP
routing domain.

Distribution List Tab

The Distribution tab of the BGP Management dialog consists of a single area, Distribution List Table. In
addition to this area, the following subarea is available: Edit Distribution List Table.

The Distribution List Table area describes filtering of routing updates sent or received by the routing
process.

•

ACL ID—Unique identifier of an ACL for filtering routing updates sent or received by a routing
process. The ACL specifies which network routes will be permitted or denied in routing updates.
This field has the following values:

–

<1-199>—Standard access list number.

–

<1300-2699>—Expanded access list number.

–

alphanumeric—Named access list.

•

Direction—Indicates whether the filter will be applied against routing updates received by the
routing process or advertised by the routing process.

–

in—Applies to updates received.

–

out—Applies to updates advertised.

•

Interface—Identifies a particular interface that the filter is applied to. For an incoming filter,
suppresses routing updates received on a specific interface; if not specified, routing updates are
suppressed on all interfaces. For an outgoing filter, suppresses routes from being advertised on a
particular interface; if not specified, route advertisements are suppressed on all interfaces.

–

Null 0

–

FastEthernet <slot>/<port> (Native IOS only)

–

GigabitEthernet <slot>/<port> (Native IOS only)

–

GE-WAN <slot>/<port>

–

POS <slot>/<port>

–

ATM <slot>/<subslot>/<port>

–

Port-channel <n> (Native IOS only)

–

VLAN <n>

•

Protocol—Identifies the routing protocol source of network routes.

«
...
380
381
382
383
384
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: T-Mobile Страницы: 4

Бренд: Ruby Tech Страницы: 17

iPAQ Connection Point CP-1

Бренд: Compaq Страницы: 50

Бренд: MikroTik Страницы: 7

WAP54GP - Wireless-G Access Point

Бренд: Linksys Страницы: 67

Бренд: iBall Baton Страницы: 62

Бренд: Ebyte Страницы: 31

Бренд: Ebyte Страницы: 22

Бренд: Ebyte Страницы: 23

Бренд: Ebyte Страницы: 26

Бренд: Eusso Страницы: 68

Era M0201AKB_uc

Бренд: CommScope Страницы: 60

Бренд: Ecox Страницы: 16

Бренд: Hama Страницы: 9

Wireless LAN Access Point

Бренд: Hama Страницы: 2

Бренд: JRC Страницы: 12

CAR 150 WiFi Duo

Бренд: Kathrein Страницы: 20

Бренд: Ebyte Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды