manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 227

 

8-81

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/T3 Interface Management Window

EIGRP 

The EIGRP area describes the EIGRP configuration of the interface on each active autonomous system. 
This area contains the following information:

•

Interface—Lists the active EIGRP routing processes on the router. Each routing process handles 
routing updates for a single autonomous system. The routing process only is active if it is deployed 
on at least one network.

•

Bandwidth Utilization (%)—Percentage of bandwidth that may be used by EIGRP on the interface. 
Values greater than 100 percent may be configured; this can be useful if the bandwidth is set 
artificially low for other reasons.

•

Hold Time (sec)—Hold time during which the device will wait for a hello packet to be received on 
the specified interface and EIGRP autonomous system number. The hold time should be at least 
three times the hello interval.

•

Hello Interval (sec)—Frequency at which the device will send hello packets on the specified 
interface and EIGRP autonomous system number.

IS–IS 

The IS-IS area contains the following information:

•

Area Tag—Identifies the IS-IS routing area that the interface participates in. If multi-area IS-IS is 
configured on the device, the IS-IS area must be named; otherwise, this value may be an implicit 
null tag. This attribute is read-only.

•

Level 1 Hello Interval—Length of time between hello packets generated on the interface for level 1 
routing. With smaller hello intervals, topological changes are detected faster, but there is more 
routing traffic.

•

Level 1 Metric—Cost of the interface for IS-IS level 1 (intra-area) route calculation.

•

Level 1 Priority—Level 1 priority. The priority is used to determine which router on a LAN will be 
the designated router or Designated Intermediate System (DIS). The router with the highest priority 
will become the DIS. In the case of equal priorities, the highest MAC address breaks the tie.

•

Level 2 Hello Interval—Length of time between hello packets generated on the interface for level 2 
routing.

•

Level 2 Metric—Cost of the interface for IS-IS level 2 (inter-area) route calculation.

•

Level 2 Priority—Level 2 priority.

•

Status—Indicates whether or not IS-IS routing is enabled on the interface. This attribute is 
read-only.

•

Enable—Enables IS-IS routing on the interface.

Note

To enable IS-IS on an interface, the user must specify an IS-IS routing process that is already 
deployed on the device. If the process does not exist, the action will fail.

•

Disable—Disables IS-IS routing on the interface.

Note

By default, all interfaces are configured as IS-IS Circuit-type Level 1-2.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды