Cisco WS-C3550-12G Скачать руководство пользователя страница 371 | Manualshive

Страница: 371 / 436

background image

11-19

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

EIGRP Management Window

Metric Default

The Metric Default subarea provides the following information:

•

Default Metric—Default OSPF metric used for redistributed routes. This metric is used when an
explicit metric is not given in the Metric entry of the Redistribution tab. A value of 0 indicates that
no default metric has been specified.

Edit Redistribution Table

This area allows changes to be made to the attributes shown in the Redistribution Table. These attributes
are discussed in detail in the

Redistribution Tab

.

•

Protocol—Source routing protocol from which routes are being distributed into EIGRP. This field
may have the following values:

–

IS-IS

–

EIGRP

–

OSPF

–

BGP

–

static

•

IS-IS Routing Level—Indicates IS-IS route level redistribution.

•

Delay—Delay metric.

•

Loading—Loading metric.

•

Source ID—Identifies the routing process from which routes are being distributed.

•

Bandwidth—Bandwidth metric.

•

Reliability—Reliability metric.

•

MTU—Maximum transmission unit of the path metric.

•

Add Redistribute—Enables route redistribution from another IP routing process into the EIGRP
routing domain. Routes may be learned from an IS-IS, OSPF, or BGP routing process.

•

Del Redistribute—Disables route redistribution from another IP routing process into the EIGRP
routing domain.

«
...
369
370
371
372
373
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Edge Pro ERPro-8

Бренд: Ubiquiti Страницы: 20

Бренд: Pakedge Страницы: 6

Бренд: Cellient Страницы: 23

Bluetooth CE Bus PhoneDongle

Бренд: Motorola Страницы: 17

Бренд: Motorola Страницы: 2

Бренд: Motorola Страницы: 1

Бренд: Motorola Страницы: 802

Бренд: Motorola Страницы: 1048

Бренд: Motorola Страницы: 836

Бренд: Motorola Страницы: 1090

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 25

Бренд: NEC Страницы: 25

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 46

Бренд: NEC Страницы: 48

Бренд: Samsung Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды