Cisco WS-C3550-12G Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 436

Cisco WS-C3550-12G Скачать руководство пользователя страница 190

8-44

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

POS Interface Management Window

Configuration Tab

The following areas are available on the Configuration tab of the POS Interface Management window:

•

General

•

Layer 2

•

Layer 3

•

Private VLAN Edge

•

Actions

General

The General area contains the following information:

•

Duplex—SONET interfaces are by definition full duplex.

•

Link Up / Down Trap—Enables or disables linkUp and linkDown trap generation for the interface.

•

Max. Input Queue Length—Displays the input queue length in packets.

•

Max. Output Queue Length—Displays the output queue length in packets.

•

Delay—Specifies the delay in tens of microseconds for an interface or network segment.

Note

The Delay attribute is an informational parameter used only to communicate the current
bandwidth to the higher-level protocols (such as IGRP and EIGRP); you cannot adjust the actual
delay of an interface with this command.

•

Bandwidth—Overwrites default bandwidth in kilobits per second.

Note

The Bandwidth attribute is an informational parameter used only to communicate the current
bandwidth to the higher-level protocols (such as IGRP, EIGRP, and OSPF); you cannot adjust
the actual bandwidth of an interface with this command.

Layer 2

The Layer 2 area contains the following information:

•

MTU—The size of the largest datagram (frame) which can be sent or received on the interface,
specified in octets.

•

Advanced Features—Launches the POS Advanced Configuration window.

«
...
188
189
190
191
192
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды