manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя, Страница: 335 / 436

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 335

 

10-27

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

EtherChannel Management Window

EIGRP 

The EIGRP area provides the following information:

•

Interface—A list of the EIGRP processes. The following attributes can be configured for a EIGRP 
process:

•

Bandwidth Utilization (%)—Percentage of the EtherChannel interface bandwidth that the EIGRP 
protocol can use.

•

Hold Time (sec)—Length of time in seconds that neighbors should consider the sender valid.

•

Hello Interval (sec)—Interval in seconds between hello packets.

ISIS 

The ISIS area provides the following information:

•

Status—Indicates whether IS-IS routing is enabled or disabled for the interface. This attribute is 
read-only. 

•

Area Tag—The IS-IS routing area in which the interface participates. If mutli-area IS-IS is 
configured on the device, the IS-IS area must be named. Otherwise, this value may be an implicit 
null tag. This attribute is read-only. 

•

Level 1 Hello Interval—Length of time between hello packets generated on the interface for level 1 
routing.

•

Level 2 Hello Interval—Length of time between hello packets generated on the interface for level 2 
routing.

•

Level 1 Metric—Cost of the interface for IS-IS level 1 (intra-area) route calculation.

•

Level 2 Metric—Cost of the interface for IS-IS level 2 (inter-area) route calculation.

•

Level 1 Priority—Determines which router on a LAN will be the designated router or Designated 
Intermediate System (DIS). 

•

Level 2 Priority—Determines which router on a LAN will be the designated router or Designated 
Intermediate System (DIS).

•

Enable IS–IS—Enable IS-IS routing on the interface. An Action Report displays result data.

Note

The specified IS-IS routing protocol must already exist (i.e., be deployed) on the device. If the 
specified process does not exist, the action will fail.

•

Disable IS-IS—Disables IS-IS routing on the interface.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов