manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 430

 

13-32

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 13      Alarms and Alarm Management

Cisco Catalyst Switch Manager Alarms

Attribute Value Alarms

Because the Catalyst switches running IOS do not support SNMP traps for hardware component failures 
or changes, the Cisco Catalyst Switch Manager software polls certain object attributes to determine 
hardware status. If the polled value indicates a failure, the Cisco Catalyst Switch Manager software 
raises an appropriate alarm. The following objects have one or more attributes polled for status 
information:

•

Chassis

•

Power Supply

•

All Modules/Port Adapters

•

Software

Chassis

The following table describes the Chassis object attribute alarms.

Table 13-10 Chassis Attribute Alarms

Attribute

Message/Description

Severity

Alarms Cleared

Core 
Temperature 
Status = ok

“C6576M Chassis Core Temperature 
Status is ok. Core temperature is within 
normal operation limits.”

Normal

Core Temperature 
Status = error
Core Temperature 
Status = critical

Core 
Temperature 
Status = error

“C6576M Chassis Core Temperature 
Status is error. The core chassis 
temperature is greater than the normal 
operating temperature range.”

Major

Core Temperature 
Status = critical

Core 
Temperature 
Status = critical

“C6576M Chassis Core Temperature 
Status is critical. The switch is going to 
shutdown due to excessively high core 
temperature.”

Critical

Core Temperature 
Status = error

Fan Status = ok

“C6576M Chassis Fan Status is ok.”

Normal

Fan Status = other
Fan Status = minorFault
Fan Status = majorFault

Fan Status = 
other

“C6576M Chassis Fan Status is other.”

Minor

Fan Status = minorFault
Fan Status = majorFault

Fan Status = 
minorFault

“C6576M Chassis Fan Status is 
minorFault.”

Major

Fan Status = other
Fan Status = majorFault

Fan Status = 
majorFault

“C6576M Chassis Fan Status is 
majorFault.”

Critical

Fan Status = other
Fan Status = minorFault

Slots Used

“C6576M Chassis Used Slots has 
changed. The switch line card 
configuration has changed.”

A change in this value initiates a 
subchassis rediscovery.

Major

None

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды