manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 135

 

7-23

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 7      Module and Port Adapter Management

SLB Module Management Window

•

Gateway Add—Adds the default gateway specified by the Gateway field and the Client Side VLAN 
field. You need to specify a VLAN in the Client Side VLAN field and an IP address in the Gateway 
field for the action to take effect.

Server Side VLAN Tab

The following areas are available on the Server Side VLAN tab of the SLB Module Management 
window:

•

Server-Side VLAN 

•

Server VLAN Config 

Server–Side VLAN 

The Server Side VLAN area provides the following information:

•

Server–Side VLAN Table—Identifies the server VLANs used by the CSM. These are the VLANs 
on the device to which servers will connect. The following attributes are displayed for the selected 
server VLANs in the table:

–

IP Address—IP address of the server VLAN.

–

Netmask—Subnet mask of the server VLAN IP address. Enabled bits indicate network 
addressing bits in the IP address.

•

Server Side VLAN Alias Table—Describes the aliases of a server VLAN. If the CSM is in a different 
subnet from the real servers, aliases may be used to eliminate the need for a router. Only used in 
server mode. There may be multiple aliases associated with each server VLAN. The following 
attributes are displayed in the table:

–

Server Side VLAN—Unique identifier of a server VLAN on the device.

–

IP Address—IP address of the server VLAN.

–

Netmask—Subnet mask of the server VLAN alias IP address. Enabled bits indicate network 
addressing bits in the IP address.

•

Server Side VLAN Static Route Table—Describes the static routes of a server VLAN. A static route 
is configured to reach a real server if it is more than one network hop away from the CSM. There 
may be multiple static routes configured for a server VLAN. The following attributes are displayed 
in the table:

–

Server Side VLAN—Unique identifier of a server VLAN on the device.

–

Destination Network—IP address of network on the server VLAN.

–

Destination Netmask—Subnet mask of the network on the server VLAN. Enabled bits indicate 
network addressing bits in the IP address.

–

Gateway—Default gateway of a server VLAN. A router to the client VLAN must have this 
gateway address configured and real servers must point their gateways to this address.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды