manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя, Страница: 231 / 436

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 231

 

8-85

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/E3 Interface Management Window

•

Connector Present—Indication if a cable is connected to the interface. If the ifAdminStatus is down, 
then this value cannot be determined and an “unknown” message is given. This attribute is read-only. 
This attribute can have the following values:

–

yes—Cable is connected to the interface.

–

no—Cable is not connected to the interface.

–

unknown—Cannot determine if a cable is connected to the interface.

•

Number of Resets—Number of times the interface internally reset. This attribute is read-only.

Performance Logging 

The Performance Logging area contains the buttons to enable data logging of all the interface attributes 
of the interface.

•

Start—Turns on performance data logging.

•

Stop—Turns off performance data logging.

Note

The logged data is available to you through the Cisco EMF Performance Manager. Refer to the 
Cisco Element Management Framework User Guide for more information about the Performance 
Manager.

Configuration Tab

The following areas are available on the Configuration tab of the ATM/E3 Interface Management 
window:

•

General

•

Layer 2

•

Layer 3

•

Private VLAN Edge

•

Actions

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов