manualshive.com logo in svg

Cisco WS-C3550-12G, Руководство пользователя

Поделиться
Скачать
Cisco WS-C3550-12G Скачать руководство пользователя страница 307

 

9-43

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 9      Software Management

MPLS Management Window

Details Tab

The following areas are available on the Details tab of the MPLS Management window:

•

MPLS

•

VC Table

•

Trouble Shooting

MPLS 

This area provides the following information:

•

MPLS Enabled—If true, MPLS is enabled on this switch.

•

Router ID—The displayable route identifier for EoMPLS. This ID is derived from the IP address of 
the interface.

•

Local LDP ID—This local label distribution protocol ID for EoMPLS.

•

Enabled—Enables MPLS on the target switch.

•

Disabled—Disables MPLS on the target switch.

VC Table

This table describes the EoMPLS virtual circuit instances and defines the following information:

•

VC ID—The virtual circuit identifier for this instance.

•

Client Interface—Name of the interface associated with the virtual circuit.

•

VC State—Current state of the virtual circuit, either ‘up’ or ‘down’.

•

Local VC Label—If assigned, the local label of the virtual circuit.

•

Remote VC Label—If assigned, the remote label of the virtual circuit.

•

Tunnel Label—The label of the tunnel associated with the virtual circuit.

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды