Cisco WS-C3550-12G Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 436

background image

8-48

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

POS Interface Management Window

Error Statistics

The Error Statistics area contains the following information:

•

CRC Error Pkts.—Number of input packets that had cyclic redundancy checksum errors.

•

In Discarded Pkts.—The number of inbound packets that were chosen to be discarded even though
no errors had been detected to prevent their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet is to free up buffer space.

•

Out Discarded Pkts.—The number of outbound packets that were chosen to be discarded even
though no errors had been detected to prevent their being transmitted. One possible reason for
discarding such a packet is to free up buffer space.

•

In Dropped Pkts.—The number of packets dropped because the input queue was full.

•

Out Dropped Pkts.—The number of packets dropped because the output queue was full.

•

In Ignored Pkts.—Number of input packets that were ignored by this interface.

•

In Aborted Pkts.—Number of input packets that were aborted.

•

In Error Pkts.—The number of inbound packets that contained errors preventing them from being
delivered to a higher-layer protocol.

•

Out Error Pkts.—Number of outbound packets that could not be transmitted because of errors.

Performance Logging

The Performance Logging area contains buttons to enable data logging of all the interface attributes of
the interface:

•

Start—Turns on performance data logging.

•

Stop—Turns off performance data logging.

Note

The logged data is available to you through the Cisco EMF Performance Manager. Refer to the
Cisco Element Management Framework User Guide for more information about the Performance
Manager.

Routing Protocol Tab

The following areas are available on the Routing Protocol tab of the POS Interface Management window:

•

OSPF

•

EIGRP

•

ISIS

•

MPLS

«
...
192
193
194
195
196
...
»

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WS-C3550-12G

Бренд: InfiNet Wireless Страницы: 100

Бренд: Meru Networks Страницы: 73

Бренд: Planet Страницы: 2

UniFi AP BeaconHD

Бренд: Ubiquiti Страницы: 11

Бренд: Lancom Страницы: 9

Бренд: HAN Страницы: 2

Бренд: NETGEAR Страницы: 4

Бренд: Nokia Страницы: 3

Бренд: Nokia Страницы: 3

Бренд: Nokia Страницы: 75

Бренд: Nokia Страницы: 84

Бренд: Nokia Страницы: 139

Бренд: Nokia Страницы: 202

Бренд: Rosewill Страницы: 6

Бренд: EnGenius Страницы: 64

Бренд: EnGenius Страницы: 71

Бренд: EnGenius Страницы: 67

Бренд: EnGenius Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды