Cisco WS-C3550-12G Скачать руководство пользователя страница 434

Страница: 434 / 436

13-36

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 13 Alarms and Alarm Management

Cisco Catalyst Switch Manager Alarms

Software

The following table describes the Software object attribute alarms.

Table 13-14 Software Attribute Alarms

Attribute

Description

Severity

Alarms Cleared

Image Backup
Status = Ok

“C6576M Software Image Backup Status is
ok. The backup was successful.”

Normal

Image Backup Status =
Error

Image Backup
Status = Failed

“C6576M Software Image Backup Status is
Failed. IOS image backup failed.”

Major

Image Restore
Status = Ok

“C6576M Software Image Restore Status is
ok. IOS image restoration was successful.”

Normal

Image Restore Status =
Error

Image Restore
Status = Failed

“C6576M Software Image Restore Status is
Failed. IOS image restoration failed.”

Do not restart the switch/router.

Critical

Configuration
Backup Status =
Ok

“C6576M Software Configuration Backup
Status is ok. Startup configuration backup
was successful.”

Normal

Configuration Backup
Status = Error

Configuration
Backup Status =
Failed

“C6576M Software Configuration Backup
Status is Failed. Startup configuration
backup failed.”

Major

Configuration
Restore Status =
Ok

“C6576M Software Configuration Restore
Status is ok. Startup configuration
restoration was successful.”

Normal

Configuration Restore
Status = Error

Configuration
Restore Status =
Failed

“C6576M Software Configuration Restore
Status is Failed. Startup configuration
restoration failed.”

Do not restart the switch/router.

Critical

Содержание WS-C3550-12G





















































































































































































































































































































































































































































Результаты поиска

Содержание WS-C3550-12G

Отзывы:

Cisco WS-C3550-12G, Руководство пользователя, Страница: 434 / 436

Результаты поиска

Содержание WS-C3550-12G

Отзывы: