Alcatel Omni Switch/Router, Руководство пользователя

Страница: 969 / 1100

Modifying a WAN Link
Page 31-9
Modifying a WAN Link
The
linkmodify
command is used to modify the parameters of an existing WAN Link. Different
parameters will be displayed by the command based on the type of link. The first subhead-
ing (
Modifying ISDN Links ) below shows the sequence of screens when modifying a link over
a WSX port. The second subheading below ( Modifying WSX Links on page 31-10) shows the
sequence of screens when modifying a link over an ISDN port.
Note
The Slot and Port fields in an existing WAN Link record
cannot be modified. To change them, you must delete
the record then create a new record.
Modifying ISDN Links
1. To modify a WAN Link, you must enter its Link Index with the command. For example, to
modify Link Index 1 which uses ISDN, you would enter the following command:
linkmodify L1
A screen similar to the following displays:
Modify ISDN call record configuration. Peer ID: 1 Link Index: 1
Type: ISDN Call Slot: 5 Port: 1
1) Link Description : Link Entry: 1, Peer ID: 1
{Enter text up to 30 characters}
2) Link Administrative Status . . . . . . . . . . . . . . . . . . . . . . . . . . = Enabled
{(E)nabled, (D)isabled}
3) Inactivity Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 30
{1-9999 seconds or 0 if disabled}
4) Minimum call duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{1-9999 seconds or 0 if disabled}
5) Maximum call duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{1-9999 seconds}
6) Outgoing Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = Enabled
{Enable, Disable}
60) Call Originate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . = On-Demand
(O)n-Demand or (B)ackup}
61) Carrier Delay Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{Call completion timeout 1-999 seconds}
62) Maximum Call Retries . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{Retry call count, 0 if infinite}
63) Retry Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{Seconds between retry attempts, 0 = retry immediately}
64) Failure Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 0
{Secs after max calls failed to retry,
0 = don't retry after max calls failed}
65) Remote Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . =
{digits 0 through 9}
66) Desired Calling Speed . . . . . . . . . . . . . . . . . . . . . . . . . = 64000
{56000, 64000}
7) Incoming calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = Enabled
{Enabled, Disabled}
(save/quit/cancel)
:
The fields on this screen are the same as those produced by the
linkadd
command. See
Adding a WAN Link on page 31-3 for descriptions of each of these fields.