System Menu
Page 9-5
System Menu
The System menu contains commands to view or set system-specific parameters. To access
this menu, enter
system
at the
UI
prompt to enter the System menu. If you are not in verbose mode, press a question
mark (
?
) and then press
<Enter>
to display the commands in the system menu, as shown
below.
Command
System Menu
info
Basic info on this system
dt
Set system date and time
ser
View or configure the DTE or DCE port
mpm
Configure a Management Processor Module
slot
View Slot Table information
systat
View system stats related to system, power and environment
taskstat
View task utilization stats
taskshow
View detailed task information
memstat
View memory use statistics
fsck
Perform a file system check on the flash file system
newfs
Erase all file from /flash and create a new file system
syscfg
View/Configure info related to this system
uic
UI configuration; change - prompt, timeout, more, verbose.
camstat
View CAM info and usage
camcfg
Configure CAM info and usage
hrex
Enter HRE-X management command sub-menu
ver/ter
Enables/disables automatic display of menus on entry (obsolete)
echo/noecho
Enable/disable character echo
chpr
Change the prompt for the system (obsolete, use ‘uic’ command
logging
View system logs.
health
Set health parameters or view health statistics
cli
Enter command line interface
saveconfig
Dump the cache configuration content to the mpm.cnf file.
cacheconfig
Set the flag to use cache configuration only.
Main
File
Summary VLAN
Networking
Interface Security
System
Services
Help
All of the System menu commands—except for the
mpm
,
ver
,
ter
,
echo
,
noecho
,
chpr
,
logging
,
health
, and
cli
commands—are described in the following sections. The
uic
,
ver
/
ter
,
echo
,
noecho
,
chpr
, and
cli
commands are described in Chapter 4, “The User Interface.” The
mpm
command is described in Chapter 6, “Configuring Management Processor Modules.”
♦
Note
♦
The
ver
,
ter
, and
chpr
commands now appear as items
in the
UI
Configuration menu (displayed through the
uic
command). If you enter the
ver
/
ter
and
chpr
commands, a message will advise you to use the
uic
command, and the
UI
Configuration menu will auto-
matically display. For more information on the
UI
Configuration menu, refer to Chapter 4, “The User
Interface.”
Содержание Omni Switch/Router
