Alcatel Omni Switch/Router, Руководство пользователя

Страница: 856 / 1100

The WAN Port Software Menu
Page 28-30
This next example displays the configuration view screen for a fractional T1 port (port 1)
using PPP. To view 3/1, enter:
wpview 3/1
or
wpv 3/1
A screen similar to following displays:
Configuration View for Slot 3, Port 1.
1)
Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UP
2) Protocol Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frame Relay
3) T1/E1 Starting Time Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4) T1/E1 Number of Time Slots . . . . . . . . . . . . . . . . . . . . . . . . . 24
8) TOS for Voice Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a0
9) TOS for Voice Signaling Data . . . . . . . . . . . . . . . . . . . . . . . . 60
10) TOS Mask for both TOS Value. . . . . . . . . . . . . . . . . . . . . . . . e0
11) Signaling IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
12) Signaling IP Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255.255.255.255
13) KeepAlive Up Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
14) KeepAlive Down Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
15) KeepAlive Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
16) DTR Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
17) DTR Pulse Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
♦
Note
♦
The DTR Pulse setting do not apply to T1 and E1
interfaces, and are not described below.
Admin Status
The options for the Admin Status are
UP
and
DN
. If
UP
, the port has been enabled and
can transmit data as long as its Operational Status is also
UP
. If set to is
DN
, the port will
not pass data even if its physical connection is good.
Protocol Type
The protocol type can be set to either Frame Relay or Point to Point Protocol (PPP). The
default setting is Frame Relay.
T1/E1 Starting Time Slot
This field specifies the first time slot number to use on a T1 or E1 port. For a full T1 or E1
connection, specify time slot 1. For a fractional T1 or E1 connection, set this field to the
starting time slot number as specified by your service provider.
T1/E1 Number of Time Slot
This field specifies the total number of 64 kbps time slots to use on the T1 or E1 connec-
tion. For a full T1, set this number to 24. For a full E1 connection, set this number to 30 if
you are running multiframe, or 31 if you are not. For fractional T1 or E1, you must set the
number of time slots to the value specified by your service provider. For example, a 256
kpbs service uses four time slots (4 x 64 = 256).