manualshive.com logo in svg

ABB SafeMove2, Руководство по применению, Страница: 197 / 238

Поделиться
Скачать
ABB SafeMove2 Скачать руководство пользователя страница 197

10 Reference information

10.1 Synchronization guidelines

10.1.1 Software synchronization guidelines

Uniquely defined position

The robot position for the synchronization must be chosen so that the position of
the robot axes are unambiguously defined. One way to make sure the
synchronization position is well-defined for all axes is to use the instruction

MoveAbsJ

to move to the sync position. See

Technical reference manual - RAPID

Instructions, Functions and Data types

.

Note that the sync position should be allowed by all active functions. For example,
the robot must be inside the allowed zones for all active Tool Position Supervision
functions.

Note

Software synchronization is always available even if hardware synchronization
is configured.

Use easily verified sync position

Select a sync position where it is easy to verify the position of the robot axes. It is
helpful to use a position where the TCP touches a spike or something where it is
easy to see if the robot is in the correct position or not.

Performing a synchronization

WARNING

If the robot position is not visually verified, to make sure all robot axes are in
correct position, the synchronization can jeopardize the safety.

Note

Synchronization can only be performed by a user with the grant

Software

synchronization

. See

Set up safety user grants on page 141

.

Action

Move the robot to its sync position
(for example with

MoveAbsJ

).

1

If an axis is in wrong position, the revolution coun-
ters are most likely incorrect.

Visually verify that the robot is in
its sync position (all axes must be
in correct position).

2

Go to the

Safety Controller

view.

3

Continues on next page

Application manual - Functional safety and SafeMove2

197

3HAC052610-001 Revision: P

© Copyright 2016-2020 ABB. All rights reserved.

10 Reference information

10.1.1 Software synchronization guidelines

Содержание SafeMove2















































































































































































































































Отзывы:

Нет отзывов