ABB SafeMove2 Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 238

ABB SafeMove2 Скачать руководство пользователя страница 183

Expected result

Action

If the Stand Still Supervision is configured to set an
output signal at violation, verify that the signal is 0
when the robot is moving and 1 when the robot is
standing still.

6

Contact Application Tolerance validation

Contact Application Tolerance only needs to be configured when using Soft Servo,
Force Control or when external forces are applied to the robot. It cannot be verified
unless it is used in one of these ways.

Expected result

Action

Make sure that Soft Servo is active and set the
stiffness to a reduced value (but not lower than
needed by the application).

1

If not permanently active, activate the activation in-
put signal for Contact Application Tolerance. Deac-
tivate all other supervision functions that are signal
activated.

2

Make sure the TCP is inside the Contact Application
Tolerance zone or all axes inside the range.

3

Status signal is 1.

If used, verify that the corresponding function active
status signal is set.

4

Run the application and verify that Contact Applica-
tion Tolerance does not trigger within the
range/zone to verify that the tolerance is high
enough.

5

Control Error Supervision will
trigger.

To verify that the tolerance values are as low as
possible, change the Soft Servo stiffness to a lower
value (e.g. 10% lower).

6

Run a RAPID program moving the TCP with maxim-
um speed allowed in the range/zone (e.g.

vmax

) in-

side the range/zone for Contact Application Toler-
ance.

Configured stop validation

Expected result

Action

Deactivate all supervision functions that are signal
activated.

1

Move the robot, for example with a move instruction.

2

The robot will stop.

Set the signal configured to stop the robot in relev-
ant operating modes.

3

Relevant operating modes are:

•

SC_GeneralStop

: All modes

•

SC_AutoStop

: Automatic mode

•

SC_EmergencyStop

: All modes.

Continues on next page

Application manual - Functional safety and SafeMove2

183

3HAC052610-001 Revision: P

© Copyright 2016-2020 ABB. All rights reserved.

6 Configuring SafeMove

6.20 Validate the configuration

Continued

«
...
181
182
183
184
185
...
»

Содержание SafeMove2















































































































































































































































Отзывы:

Нет отзывов