Zte ZXMW NR8250 Manual Download Page 5

Page: 5 / 124

2.2.21 134237756 TU-LOP ............................................................................. 2-39

2.2.22 134237928 HP-RDI .............................................................................. 2-40

2.2.23 134237929 AU-AIS............................................................................... 2-41

2.2.24 134237930 AU-LOP ............................................................................. 2-42

2.2.25 134237933 RS-TIM .............................................................................. 2-42

2.2.26 134237934 E1-AIS ............................................................................... 2-43

2.2.27 134239928 Radio link failure alarm........................................................ 2-44

2.2.28 134239929 Baseband alarm ................................................................. 2-45

2.2.29 134239930 RF ODU fault...................................................................... 2-47

2.2.30 134239931 Transmission unit invalid ..................................................... 2-49

2.2.31 134239935 ODU mute .......................................................................... 2-49

2.2.32 134241729 Ethernet port disconnected .................................................. 2-50

2.2.33 134243751 RMEP CCM packet lost....................................................... 2-51

2.2.34 134243752 RMEP CCM packet error..................................................... 2-52

2.2.35 134243753 RMEP port status abnormal................................................. 2-52

2.2.36 134243754 RMEP RDI ......................................................................... 2-53

2.2.37 134243755 Ethernet devices cross-connected ....................................... 2-53

2.2.38 134243756 Frame loss rate exceeding the threshold .............................. 2-54

2.2.39 134243757 Link delay exceeding the threshold ...................................... 2-55

2.2.40 134243758 Link delay jitter exceeding the threshold ............................... 2-55

2.2.41 134243769 EFM local link fault.............................................................. 2-56

2.2.42 134243770 EFM remote link fault .......................................................... 2-56

2.2.43 134243771 EFM discovery process failure ............................................. 2-57

2.2.44 134243776 EFM local link lost............................................................... 2-58

2.2.45 134317734 ODU link broken ................................................................. 2-59

2.2.46 134317743 SNCP channel changeover Interruption................................ 2-59

2.3 Handling Alarm ................................................................................................ 2-60

2.3.1 134218745 Insufficient flash memory ...................................................... 2-60

2.3.2 134243738 OSPF interface configuration error......................................... 2-61

2.3.3 134243739 OSPF virtual link interface configuration error ......................... 2-61

2.3.4 2002 Communication link between boards broken .................................... 2-62

2.3.5 6201 Software loading failure .................................................................. 2-63

2.3.6 6203 Software version synchronization failure between active board and

standby board....................................................................................... 2-63

2.3.7 6204 Board software fault ....................................................................... 2-64

2.3.8 6206 Running software version fault ........................................................ 2-65

2.3.9 6209 Main control software version synchronization failure ....................... 2-66

2.3.10 6213 Board inserted incorrectly ............................................................. 2-67

III

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands