Zte ZXMW NR8250 Manual Download Page 50

Page: 50 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code 10: STM-1 of optical port 2 (LMT displays "2STM-1").

Effect on the System

The signal transmitted on the SDH link is interrupted.

Possible Causes

C2 of the upstream service is configured incorrectly.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Check whether the C2 of upstream equipment is configured correctly.

If yes, modify the C2 and issue it again.

If no, go to step 2.

The alarm is caused by RTUB board failure. Replace the board.

2.2.16 134237749 TU-UNEQ

Alarm Property

Alarm Code: 134237749

Alarm Information: The alarm is reported if tributary unit is not equipped.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Each subcode represents a timeslot. The former 63 timeslots are used for optical port 1,

and the latter 63 timeslots are used for optical port 2.

Effect on the System

The signal transmitted on the SDH link is interrupted.

Possible Causes

The upstream service configuration is incorrect.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Contact the network engineer.

2-36

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands