Zte ZXMW NR8250 Manual Download Page 35

Page: 35 / 124

Chapter 2 Alarm

2.1.27 9003 SPD-C Broken

Alarm Property

Alarm Code: 9003

Alarm Information: The class C arrester loop is faulty.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The lightning protector fails.

Possible Causes

The lightning protector is damaged.

The air break switch of the lightning protector is disconnected.

The lightning protector's base is of bad contact.

The lightning protector's detecting cable is disconnected or of bad contact.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

Handling Procedure

The lightning protector is damaged. Replace the lightning protector;

Check whether the lightning protector's air break switch is closed;

Check whether the lightning protector's base is of bad contact;

Check whether the contact of the lightning protector's base is disconnected or of bad

contact;

Check the monitoring unit's connection;

Replace the monitoring unit.

2.1.28 9004 SPD-D Broken

Alarm Property

Alarm Code: 9004

Alarm Information: The class D arrester loop is faulty.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

2-21

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands