Zte ZXMW NR8250 Manual Download Page 74

Page: 74 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code Description

None

Effect on the System

The traffic is interrupted during changeover.

Possible Causes

The master or slave channel is unavailable.

Handling Procedure

Perform active/standby channel changeover manually or forcedly.

2.3 Handling Alarm

2.3.1 134218745 Insufficient flash memory

Alarm Property

Alarm Code: 134218745

Alarm Information: This alarm is reported when flash memory does not have sufficient

space.

Alarm Level: Major

Alarm Type: Handling Alarm

Sub-code Description

None

Effect on the System

This alarm does not affect any traffic, but it may cause data saving failure.

Possible Causes

The flash memory is insufficient.

Handling Procedure

In Version Management (Path:

Maintenance > Version

), delete the backup version

package file.

2-60

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands