Zte ZXMW NR8250 Manual Download

Page: 115 / 124

Chapter 3 Notification

3.30 134243764 The port quitting a LAG due to

exception

Notification Property

Notification Code: 134243764

Notification Information: The notification is reported when an aggregated port quits

from a LAG due to some exception.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

The port is blocked for some time.

Possible Causes

An LAG member port has PhyDown or Admin Down fault, which causes the port to

exit from the LAG.

The duplex mode of the LAG ports changes to non-full-duplex.

Handling Procedure

Check the property configuration of the LAG member ports. Ensure that the port

configurations are consistent for the two aggregation member devices.

Check the networking configuration and ensure that the aggregation ports are

operating properly.

3.31 134243773 EFM remote link event

Notification Property

Notification Code: 134243773

Notification Information: The notification is reported if EFM receives a link event from

the remote end.

Notification Type: Qos Alarm

Sub-code Description

Sub-code 1: Errored Symbol Period Event

Sub-code 2: Errored Frame Event

Sub-code 3: Errored Frame Period Event

Sub-code 4: Errored Frame Seconds Summary Event

Sub-code 5: Organization Specific Event

3-19

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands