Zte ZXMW NR8250 Manual Download

Page: 51 / 124

Chapter 2 Alarm

2.2.17 134237751 HP-TIM

Alarm Property

Alarm Code: 134237751

Alarm Information: The alarm is reported if higher-order path trace identification is

mismatched. This is detected by J1.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: STM-1 of optical port 1 (LMT displays "STM-1");

Sub-code 5: Path 1 of optical port 2 (LMT displays "STM-4-Channel1");

Sub-code 6: Path 2 of optical port 2 (LMT displays "STM-4-Channel2");

Sub-code 7: Path 3 of optical port 2 (LMT displays "STM-4-Channel3");

Sub-code 8: Path 4 of optical port 2 (LMT displays "STM-4-Channel4");

Sub-code 10: STM-1 of optical port 2 (LMT displays "2STM-1").

Effect on the System

The carried services are affected..

Possible Causes

The J1 byte received by the NR8250 is inconsistent with that sent by the upstream

equipment.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Check whether the transmission value of

VC-4 path access point identifier (J1 byte)

of the upstream equipment and the J1 expectation value of the local equipment are

both

-ZTE-MW-NR8250-

If yes, go to step 2.

If no, modify the two as

-ZTE-MW-NR8250-

The fault is caused by RTUB board failure. Replace the board.

2.2.18 134237752 TU-TIM

Alarm Property

Alarm Code: 134237752

Alarm Information: The alarm is reported if tributary unit trace is mismatched.

Alarm Level: Major

Alarm Type: Communications Alarm

2-37

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands