Zte ZXMW NR8250 Manual Download

Page: 97 / 124

Chapter 3

Notification

Table of Contents

10001 Board power-on completed..............................................................................3-2

10002 Standby board power-on completed ................................................................3-2

10003 PM active-to-standby changeover completed...................................................3-3

10004 PM standby-to- changeover completed............................................................3-3

10006 Board power-on failure ....................................................................................3-4

10012 Module reset....................................................................................................3-4

10013 Module status error..........................................................................................3-5

10014 Changeover completed....................................................................................3-5

10015 Changeover failure ..........................................................................................3-6

10016 Board changeover failure.................................................................................3-7

134243728 LLDP global enable status changed.........................................................3-7

134243729 Local management address of LLDP changed.........................................3-8

134243730 Neighbor information of LLDP changed....................................................3-9

134243731 8032 port blocked ....................................................................................3-9

134243732 8032 port unblocked ..............................................................................3-10

134243733 OSPF interface status changed ............................................................. 3-11

134243734 OSPF virtual interface status changed ................................................... 3-11

134243735 OSPF neighbor status changed .............................................................3-12

134243736 OSPF virtual neighbor status changed ...................................................3-12

134243740 OSPF interface receiving incorrect packet .............................................3-13

134243741 OSPF virtual link interface receiving incorrect packet .............................3-13

134243742 OSPF interface receiving incorrect LSR packet......................................3-14

134243743 OSPF interface receiving incorrect DD packet sequence number ..........3-15

134243744 Hello packet received at OSPF interface does not include the router .....3-15

134243745 Timeout for receiving OSPF hello packet ...............................................3-16

134243746 OSPF interface disabled by administrator ..............................................3-16

134243747 OSPF interface disabled physically ........................................................3-17

134243748 interface's neighbor changed .................................................................3-17

134243763 The port failing to be aggregated into a LAG ..........................................3-18

134243764 The port quitting a LAG due to exception ...............................................3-19

134243773 EFM remote link event ...........................................................................3-19

134243774 EFM loopback indication ........................................................................3-20

134243777 Local Discovery process reset ..............................................................3-21

134317731 Configuration file reloaded .....................................................................3-21

134317735 ODU firmware upgraded ........................................................................3-22

134317740 RMU switchover.....................................................................................3-23

134317745 ACM change..........................................................................................3-23

3-1

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands