Zte ZXMW NR8250 Manual Download Page 88

Page: 88 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code Description

Smoke alarm dry contact

Effect on the System

The outdoor monitoring device is abnormal. It does not affect the system performance.

Possible Causes

The smoke condition of the outdoor monitoring device is abnormal.

Handling Procedure

None

2.4.10 4016 Outdoor lightning protection module alarm

Alarm Property

Alarm Code: 4016

Alarm Information: The lightning protection module of the outdoor monitoring device

is abnormal is abnormal.

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

Sub-code 1: Lightning protection dry contact 1 is abnormal.

Sub-code 2: Lightning protection dry contact 2 is abnormal.

Effect on the System

The outdoor monitoring device is abnormal. It does not affect the system performance.

Possible Causes

The lightning protection module of the outdoor monitoring device is abnormal.

Handling Procedure

None

2.4.11 4017 outdoor power supply dry contact alarm

Alarm Property

Alarm Code: 4017

Alarm Information: power supply was abnormal

Alarm Level: Major

2-74

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands