Zte ZXMW NR8250 Manual Download Page 118

Page: 118 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Handling Procedure

Ensure that the entire table configuration file is complete. If it is not complete, use a

complete file to replace it.

3.35 134317735 ODU firmware upgraded

Notification Property

Notification Code: 134317735

Notification Information: The notification is reported if the Outdoor Unit (

ODU

) soft-

ware is upgraded through local Indoor Unit (

IDU

) or in File Transfer Protocol (

FTP

)

mode.

Notification Type: Handling Alarm

Sub-code Description

Sub-code 0: Upgrading fails;

Sub-code 1: Upgrading succeeds.

Effect on the System

This notification is due to that users upgrade software manually. It does not affect the

services.

Possible Causes

If software upgrading through IDU fails, the alarm may be due to that version files are

incomplete or incorrect.

If software upgrading in FTP mode fails, the alarm may be due to that the FTP server

setting or FTP software setting is incorrect, the version files are incomplete or incorrect.

Handling Procedure

It is a notification that notifies users to upgrade the ODU software manually.

If the software upgrading through IDU fails, ensure that the ODU software version files

saved in IDU flash memory are correct and complete.

If the software upgrading in FTP mode fails, ensure that:

The IP address of the FTP server is set correctly.

The user name and password of the FTP software are set correctly.

The new software files are correct and complete.

3-22

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands